General Information:
Material GroupS - Superalloys (Heat resistant and Titanium)
Sub-GroupTitanium alloy
Hardne32.0 HRC
Tensile Strength1000 [N/mm^2]
Machinability20%

Machining Material Ti-15-333

Material Ti-15-333 is a titanium alloy with a hardness of 32 HRC and a machinability rating of 20%.

Titanium alloys such as Ti-15-333 are used in mechanical components for two main reasons:

  • It has an excellent strength-to-weight ratio. On the one hand, it is almost as light as aluminum, and on the other hand, it has a higher strength than most steel alloys.
  • It has superb corrosion resistance.

The main challenges of machining Ti-15-333 are:

  • Ti-15-333 has very low heat conductivity. It causes heat generating from the cut to transfer mainly to the cutting tool instead of flowing to the chips and workpiece.
  • It has high flexibility, thus bending easily by the cutting forces.
  • High hardness of 32 HRC leads to premature wear.

Tip for machining Ti-15-333:

  • Use a positive cutting edge in medium/roughing operation, preferably gound with a small honing size.
  • In finish operations, use only ground inserts/tools with sharp cutting edges and minimal honing size.
  • On supper-finish applications, you can also use cutting tools that are designed for aluminum without honing.
  • On small diameter parts, on a workpiece with thin walls, or poorly clamped workpiece, be gentle with your depth of cut and feed rate to reduce the cutting force.
  • Use an insert/tool with a very hard substrate because Ti-15-333 has a hardness of 32 HRC

Summery:

  • For detailed carbide grades recommendations, check the Below Chart, or use the Grades Wizrad.
  • Recommended Cutting speed range for turning at stable conditions is 230 - 300 [SFM] / 70 - 90 [m/min].
  • Recommended Cutting speed range for milling with stable clamping and short overhang is 160 - 230 [SFM] / 50 - 70 [m/min]
  • For detailed cutting speed recomendations, check the Below Table, or use our Speed and Feed Calculator.

  • Equivalent International Designations for Material Ti-15-333

    StandardName
    unsUNS R58153

    Chemical Composition for Material Ti-15-333

    ElementAmount
    Chromium (Cr)3%
    Aluminum (Al)3%
    Iron (Fe)0.12%
    Carbon (C)0.02%

    Cutting Speeds Recomendations for Material Ti-15-333

    * Click on the speeds below for higher precision in specific conditions!

    ApplicationVc (m/min)Vc (SFM)
    Turning70-90230-300
    Milling50-70160-230
    Parting45-60150-200
    Grooving60-80200-260
    Drilling60-80200-260

    Important! The speed estimation is given for an ideal situation:

    • Most suitable carbide grade
    • Stable tool clamping
    • Stable workpiece clamping
    • Good quality raw material
    • A short overhang of the cutting tool.
    • Nominal hardness of the material.
    • etc.
    Click on the speeds in the above table to get better precision for specific parameters
    Or use our Speed and Feed Calculator



    Recommended Carbide Grades for Material Ti-15-333

    * If you don't understand the below table? Read This Explanation to make the most out of it!

    Grade for Turning

    Grade for Parting Off

    Grade for Grooving

    Grade for Milling (Indexable)

    Recommended Insert Cutting Edge Geometry for Material Ti-15-333

    Honing Siz0.02-0.05 mm / 0.001-0.002"
    Rake Angl13° -18°
    Land AnglNeutral
    Land Widt0.10-0.20 mm / 0.004-0.008"
    Ground InserRecommended

    Learn more about carbide inserts Cutting-Edge Geometry Parameters.

    Subscribe to out Newsletter and Get the Free Machinability eBook
    Scroll to Top