- Application Range
- Compatible Grades
- Cutting Speeds
Tungaloy - AH725 Menu
| General Information: | ||
|---|---|---|
| Brand | Tungaloy | |
| Grade Status | Primary | |
| Application | Turning / Milling / Parting / Grooving | |
| Substrate Class | Semi Hard | |
| Coat Type | Thin PVD | |
| Post Treat | Y | |
From Tungaloy's website:
- Good balance between wear and chipping resistance - Suitable for machining steel and stainless steel under general cutting conditions
Application Range for AH725
* If you don't understand the below table? Read This Explanation to make the most out of it!
| ISO | Material Group | app | pmksort | App | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| P | Steel | T | 0 | Turning | P15 - P30 | P | P | P | P | |||||
| M | Stainless Steel | T | 1 | Turning | M15 - M30 | M | M | M | M | |||||
| P | Steel | M | 0 | Milling | P15 - P30 | P | P | P | P | |||||
| M | Stainless Steel | M | 1 | Milling | M15 - M30 | M | M | M | M | |||||
| K | Cast Iron | M | 2 | Milling | K15 - K30 | K | K | K | K | |||||
| S | Superalloys | M | 4 | Milling | S15 - S25 | S | S | S | ||||||
| P | Steel | P | 0 | Parting | P15 - P30 | P | P | P | P | |||||
| M | Stainless Steel | P | 1 | Parting | M15 - M30 | M | M | M | M | |||||
| K | Cast Iron | P | 2 | Parting | K25 - K30 | K | K | |||||||
| S | Superalloys | P | 4 | Parting | S15 - S25 | S | S | S | ||||||
| P | Steel | G | 0 | Grooving | P15 - P30 | P | P | P | P | |||||
| M | Stainless Steel | G | 1 | Grooving | M15 - M30 | M | M | M | M | |||||
| K | Cast Iron | G | 2 | Grooving | K25 - K30 | K | K | |||||||
| S | Superalloys | G | 4 | Grooving | S15 - S25 | S | S | S |
Equivalent Grades for AH725
The most compatible grade from each brand!
A higher score (Up to 100%) means the grades are more compatible. A lower score or a particular grade not listed does not mean it is not a good grade. It means that its physical and mechanical properties are less close to AH725
| Brand | Application | Grade | Substrate | Coating | Gscore |
|---|---|---|---|---|---|
| Sandvik | Turning | GC1105 | Hard | Thin PVD | 80% |
| Iscar | Turning | IC6015 | Semi Hard | Thin CVD | 75% |
| Kennametal | Turning | KCU25 | Semi Hard | Thin PVD | 90% |
| Walter | Turning | WKK25S | Semi Hard | PVD | 85% |
| Seco | Turning | CP500 | Semi Hard | Thin PVD | 90% |
| Mitsubishi | Turning | MP9015 | Hard | PVD | 85% |
| Sumitomo | Turning | AC1030U | Semi Hard | Thin PVD | 95% |
| Sandvik | Milling | S30T | Semi Hard | Thin PVD | 90% |
| Iscar | Milling | IC808 | Semi Hard | PVD | 95% |
| Kennametal | Milling | KC520M | Hard | PVD | 80% |
| Walter | Milling | WKK25S | Semi Hard | PVD | 85% |
| Seco | Milling | MP3000 | Hard | Thin PVD | 85% |
| Mitsubishi | Milling | MP7140 | Semi Hard | PVD | 90% |
| Sumitomo | Milling | ACU2500 | Semi Hard | Thin PVD | 95% |
| Sandvik | Parting | GC1105 | Hard | Thin PVD | 80% |
| Iscar | Parting | IC808 | Semi Hard | PVD | 95% |
| Kennametal | Parting | KCU25 | Semi Hard | Thin PVD | 90% |
| Walter | Parting | WSM23S | Semi Tough | Thin PVD | 90% |
| Seco | Parting | CP500 | Semi Hard | Thin PVD | 90% |
| Mitsubishi | Parting | VP20RT | Semi Hard | PVD | 85% |
| Sumitomo | Parting | AC1030U | Semi Hard | Thin PVD | 95% |
| Sandvik | Grooving | GC1125 | Hard | PVD | 75% |
| Iscar | Grooving | IC808 | Semi Hard | PVD | 95% |
| Kennametal | Grooving | KCU25 | Semi Hard | Thin PVD | 90% |
| Walter | Grooving | WSM23S | Semi Tough | Thin PVD | 90% |
| Seco | Grooving | CP500 | Semi Hard | Thin PVD | 90% |
| Mitsubishi | Grooving | VP20RT | Semi Hard | PVD | 85% |
| Sumitomo | Grooving | AC1030U | Semi Hard | Thin PVD | 95% |
Cutting Speed recommendations for AH725
How to use our Cutting Speeds Recommendations
- Pay attention that your desired unit (SFM or m/min) is selected!
- Speeds are given for stable conditions of Machine, Tool, and workpiece.
- An empty cell means the grade is not available for the combination of material and application.
- For more specific Cutting Speeds Recommendations use our advanced
SPEEDS AND FEEDS CALCULATOR
Unit Selector:
SFM
m/min
| uid | _ | Material Group | Turning (m/min) | Turning (SFM) | Parting (m/min) | Parting (SFM) | Grooving (m/min) | Grooving (SFM) | Milling (m/min) | Milling (SFM) | Driiling (mm/min) | Drilling (SFM) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| s640f39c1decd | P | Free-Cut Steel | 170 - 330 | 510 - 1000 | 145 - 285 | 440 - 860 | 135 - 265 | 410 - 800 | 190 - 370 | 570 - 1120 | - | - |
| s640f39c1decd | P | Low Carbon Steel (0.1-0.25%) | 160 - 195 | 480 - 590 | 135 - 170 | 410 - 510 | 125 - 155 | 380 - 470 | 175 - 220 | 530 - 670 | - | - |
| s640f39c1decd | P | Carbon Steel (0.26-0.50%) | 135 - 195 | 410 - 590 | 115 - 170 | 350 - 510 | 105 - 155 | 320 - 470 | 150 - 220 | 450 - 670 | - | - |
| s640f39c1decd | P | High Carbon Steel (0.51-1.0%) | 110 - 135 | 330 - 410 | 95 - 115 | 280 - 350 | 90 - 105 | 270 - 320 | 120 - 150 | 360 - 450 | - | - |
| s640f39c1decd | P | Low Alloyed Steel (180 HB Max) | 170 - 205 | 510 - 620 | 145 - 175 | 440 - 530 | 135 - 165 | 410 - 500 | 190 - 230 | 570 - 700 | - | - |
| s640f39c1decd | P | Low Alloyed Steel (180-275 HB) | 95 - 170 | 280 - 510 | 85 - 145 | 250 - 440 | 80 - 135 | 240 - 410 | 110 - 190 | 330 - 570 | - | - |
| s640f39c1decd | P | Low Alloyed Steel (275 -350 HB) | 60 - 95 | 180 - 280 | 55 - 85 | 160 - 250 | 50 - 80 | 150 - 240 | 70 - 110 | 210 - 330 | - | - |
| s640f39c1decd | P | Tool Steel and High Alloy Steel (Annealed) | 55 - 135 | 160 - 410 | 50 - 115 | 150 - 350 | 45 - 105 | 130 - 320 | 65 - 150 | 190 - 450 | - | - |
| s640f39c1decd | P | Tool Steel and High Alloy Steel (250-300 HB) | 40 - 95 | 120 - 280 | 35 - 85 | 100 - 250 | 35 - 80 | 100 - 240 | 45 - 110 | 130 - 330 | - | - |
| s640f39c1decd | M | Ferritic Stainless Steel | 90 - 235 | 270 - 710 | 60 - 155 | 180 - 470 | 80 - 205 | 240 - 620 | 95 - 250 | 280 - 760 | - | - |
| s640f39c1decd | M | Martensitic Stainless Steel | 90 - 145 | 270 - 440 | 60 - 95 | 180 - 280 | 80 - 125 | 240 - 380 | 95 - 150 | 280 - 450 | - | - |
| s640f39c1decd | M | Austenitic Stainless Steel | 90 - 120 | 270 - 360 | 60 - 75 | 180 - 220 | 80 - 100 | 240 - 300 | 95 - 125 | 280 - 380 | - | - |
| s640f39c1decd | M | Duplex Stainless Steel | 25 - 80 | 70 - 240 | 15 - 50 | 40 - 150 | 25 - 70 | 70 - 210 | 30 - 85 | 90 - 250 | - | - |
| s640f39c1decd | M | Precipitation Hardening St. St. | 105 - 130 | 320 - 390 | 70 - 85 | 210 - 250 | 90 - 115 | 270 - 350 | 110 - 140 | 330 - 420 | - | - |
| s640f39c1decd | K | Grey Cast Iron (180 HB Max) | - | - | 125 - 170 | 380 - 510 | 90 - 115 | 270 - 350 | 165 - 215 | 500 - 650 | - | - |
| s640f39c1decd | K | Grey Cast Iron (180-260 HB) | - | - | 75 - 135 | 220 - 410 | 55 - 95 | 160 - 280 | 100 - 175 | 300 - 530 | - | - |
| s640f39c1decd | K | Nodular cast iron (160 HB Max) | - | - | 125 - 185 | 380 - 560 | 90 - 130 | 270 - 390 | 165 - 240 | 500 - 730 | - | - |
| s640f39c1decd | K | Nodular cast iron (180-280 HB) | - | - | 55 - 120 | 160 - 360 | 35 - 85 | 100 - 250 | 70 - 155 | 210 - 470 | - | - |
| s640f39c1decd | K | Malleable cast iron (180 HB Max) | - | - | 120 - 175 | 360 - 530 | 80 - 125 | 240 - 380 | 150 - 230 | 450 - 700 | - | - |
| s640f39c1decd | K | Malleable cast iron (180-270 HB) | - | - | 55 - 120 | 160 - 360 | 35 - 80 | 100 - 240 | 70 - 150 | 210 - 450 | - | - |
| s640f39c1decd | S | Iron (Fe) Based - Supper Alloys | - | - | 40 - 85 | 120 - 250 | 60 - 115 | 180 - 350 | 65 - 130 | 190 - 390 | - | - |
| s640f39c1decd | S | Nickel (Ni) Based - Supper Alloys (20 HRC Max | - | - | 25 - 75 | 70 - 220 | 35 - 105 | 100 - 320 | 40 - 120 | 120 - 360 | - | - |
| s640f39c1decd | S | Nickel (Ni) Based - Supper Alloys (21-42 HRC) | - | - | 15 - 30 | 40 - 90 | 20 - 45 | 60 - 130 | 25 - 50 | 70 - 150 | - | - |
| s640f39c1decd | S | Cobalt (Co) Based - Supper Alloys | - | - | 10 - 30 | 30 - 90 | 15 - 45 | 40 - 130 | 15 - 50 | 40 - 150 | - | - |
| s640f39c1decd | S | Pure Titaium | - | - | 45 - 75 | 130 - 220 | 65 - 105 | 190 - 320 | 75 - 120 | 220 - 360 | - | - |
| s640f39c1decd | S | Titanium alloys | - | - | 25 - 50 | 70 - 150 | 35 - 70 | 100 - 210 | 40 - 80 | 120 - 240 | - | - |
