- Equivalent Standards
- Chemical Composition
- Cutting Speeds Recommendation
- Recommended Carbide Grades
- Cutting Edge Geometry
Material Incoloy 020 Menu:
| General Information: | ||
|---|---|---|
| Material Group | S - Superalloys (Heat resistant and Titanium) | |
| Sub-Group | Superalloy | |
| Tensile Strength | [N/mm^2] | |
| Machinability Range | 25% - 50% | |
Equivalent International Designations for Material Incoloy 020
| Standard | Name |
|---|---|
| sae | ASTM B463 |
| wnr | 2.4660 |
| anfor | 20CB-3 |
Chemical Composition for Material Incoloy 020
| Element | Amount |
|---|---|
| Iron (Fe) | 38.0% |
| Nickel (Ni) | 34% |
| Chromium (Cr) | 20% |
| Cobalt (Co) | 2.5% |
Cutting Speeds Recomendations for Heat resistant Fe Based
* Click on the speeds below for higher precision in specific conditions!
| Application | Vc (m/min) | Vc (SFM) |
|---|---|---|
| Turning | 100-200 | 330-660 |
| Milling | 75-150 | 250-490 |
| Parting | 65-125 | 210-410 |
| Grooving | 90-175 | 300-570 |
| Drilling | 90-175 | 300-570 |
Important! The speed estimation is given for an ideal situation:
- Most suitable carbide grade
- Stable tool clamping
- Stable workpiece clamping
- Good quality raw material
- A short overhang of the cutting tool.
- Nominal hardness of the material.
- etc.
Click on the speeds in the above table to get better precision for specific parameters
Or use our Speed and Feed Calculator
Recommended Carbide Grades for Material Incoloy 020
* If you do nott understand the below table? Read This Explanation to make the most out of it!
Grade for Turning
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | S05F | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | CVD | S05 - S10 | S | S | |||||||
| Sandvik | GC1105 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S15 | S | S | |||||||
| Sandvik | GC1115 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S20 | S | S | |||||||
| Sandvik | GC1125 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S30 | S | S | S | ||||||
| Iscar | IC806 (IC804) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S20 | S | S | S | S | |||||
| Iscar | IC807 (IC907) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S25 | S | S | S | S | |||||
| Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
| Kennametal | KCU10 (KC5010) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
| Kennametal | KCU25 (KC5025) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S30 | S | S | S | ||||||
| Walter | WSM10S (WSM10) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S20 | S | S | S | S | |||||
| Walter | WSM01 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S05 | S | ||||||||
| Walter | WSM20S (WSM20) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S30 | S | S | S | S | S | ||||
| Walter | WSM30S (WSM30) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S40 | S | S | S | S | S | ||||
| Seco | TS2000 (CP200) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S25 | S | S | S | S | S | ||||
| Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S25 | S | S | S | ||||||
| Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
| Seco | TS2500 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
| Tungaloy | AH8005 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S10 | S | S | |||||||
| Tungaloy | AH8015 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
| Mitsubishi | MP9005 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S15 | S | S | S | ||||||
| Mitsubishi | MP9015 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
| Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S35 | S | S | S | S | S | ||||
| Sumitomo | AC5005S (AC510U) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S10 | S | S | |||||||
| Sumitomo | AC5015S | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S15 | S | S | S | ||||||
| Sumitomo | AC5025S (AC520U) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S30 | S | S | S | S | S |
Grade for Milling (Indexable)
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | S30T | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S30 | S | S | S | S | S | ||||
| Sandvik | S40T | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S25 - S40 | S | S | S | S | |||||
| Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Iscar | IC830 (IC928) | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S20 - S40 | S | S | S | S | S | ||||
| Kennametal | KC510M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S10 | S | S | |||||||
| Kennametal | KC522M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S30 | S | S | S | S | |||||
| Kennametal | KCSM40 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S25 - S40 | S | S | S | S | |||||
| Seco | MS2500 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S05 - S25 | S | S | S | S | S | ||||
| Seco | F40M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Seco | MS2050 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S35 | S | S | S | S | S | S | |||
| Tungaloy | AH120 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S25 | S | S | S | S | |||||
| Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S25 | S | S | S | ||||||
| Mitsubishi | MP9120 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Mitsubishi | MP9130 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S35 | S | S | S | S | S | ||||
| Sumitomo | ACU2500 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Sumitomo | ACM200 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S10 - S30 | S | S | S | S | S | ||||
| Sumitomo | ACM300 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S20 - S40 | S | S | S | S | S |
Grade for Parting Off
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | GC1105 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S20 | S | S | S | S | |||||
| Sandvik | GC1145 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
| Iscar | IC807 (IC907) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S10 | S | S | |||||||
| Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
| Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S25 - S40 | S | S | S | S | |||||
| Kennametal | KCU10 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S15 | S | S | S | ||||||
| Kennametal | KCU25 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S30 | S | S | S | S | |||||
| Walter | WSM13S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S20 | S | S | S | S | |||||
| Walter | WSM23S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S30 | S | S | S | S | S | ||||
| Walter | WSM33S (WSM33) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
| Walter | WSM43S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S30 - S45 | S | S | S | S | |||||
| Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S30 | S | S | S | S | S | ||||
| Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
| Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S25 | S | S | S | ||||||
| Tungaloy | AH7025 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S25 | S | S | S | ||||||
| Mitsubishi | VP10RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S10 | S | S | |||||||
| Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
| Mitsubishi | VP30RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S25 - S40 | S | S | S | S | |||||
| Sumitomo | AC520U | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
| Sumitomo | AC1030U (AC530U) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S |
Grade for Grooving
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | GC1125 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S30 | S | S | S | S | S | ||||
| Iscar | IC806 (IC804) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S15 | S | S | S | ||||||
| Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
| Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S25 - S35 | S | S | S | ||||||
| Kennametal | KCU10 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S20 | S | S | S | S | |||||
| Kennametal | KCU25 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S30 | S | S | S | ||||||
| Walter | WSM13S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S20 | S | S | S | S | |||||
| Walter | WSM23S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S30 | S | S | S | S | S | ||||
| Walter | WSM33S (WSM33) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S40 | S | S | S | S | S | ||||
| Walter | WSM43S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S30 - S45 | S | S | S | S | |||||
| Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S20 | S | S | |||||||
| Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S35 | S | S | S | S | |||||
| Tungaloy | AH905 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S10 | S | S | |||||||
| Tungaloy | AH7025 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
| Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
| Mitsubishi | VP10RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S10 | S | S | |||||||
| Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S25 | S | S | S | S | |||||
| Mitsubishi | VP30RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S25 - S40 | S | S | S | S | |||||
| Sumitomo | AC520U | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S25 | S | S | S | S | |||||
| Sumitomo | AC1030U (AC530U) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S40 | S | S | S | S | S |
Recommended Insert Cutting Edge Geometry for Material Incoloy 020
| Honing Size: | 0.02-0.05 mm / 0.001-0.002" | |
| Rake Angle: | 13° -18° | |
| Land Angle: | Neutral | |
| Land Width: | 0.10-0.20 mm / 0.004-0.008" | |
| Ground Insert: | Recommended |
Learn more about carbide inserts Cutting-Edge Geometry Parameters.
Our Top Picks
