General Information: | ||
---|---|---|
Material Group | N - Non-Ferrous (Aluminum, Brass, Plastic) | |
Sub-Group | N/A | |
Hardness | 150.0 HB | |
Tensile Strength | 570 [N/mm^2] | |
Machinability | 170% |
Equivalent International Designations for Aluminium 7075
Standard | Name |
---|---|
sae | 7075 |
wnr | 3.4365 |
din | AlZnMgCu1,5 |
bs | DTD5074 |
anfor | A-Z5GU |
uni | 3735 |
Chemical Composition for Aluminium 7075
Element | Amount |
---|---|
Zinc (Zn) | 5.1~6.1% |
Magnesium (Mg) | 2.1~2.9% |
Copper (Cu) | 1.2~2.0% |
Iron (Fe) | 0.5% |
Silicon (Si) | 0.4% |
Manganese (Mn) | 0.3% |
Titanium (Ti) | 0.2% |
Aluminum (Al) | rem% |
Cutting Speeds Recomendations for Aluminium 7075
* Click on the speeds below for higher precision in specific conditions!
Application | Vc (m/min) | Vc (SFM) |
---|---|---|
Turning | 320-435 | 1050-1430 |
Milling | 400-545 | 1310-1790 |
Parting | 215-290 | 710-950 |
Grooving | 270-360 | 890-1180 |
Drilling | 135-180 | 440-590 |
Important! The speed estimation is given for an ideal situation:
- Most suitable carbide grade
- Stable tool clamping
- Stable workpiece clamping
- Good quality raw material
- A short overhang of the cutting tool.
- Nominal hardness of the material.
- etc.
Click on the speeds in the above table to get better precision for specific parameters
Or use our Speed and Feed Calculator
Recommended Carbide Grades for Aluminium 7075
* If you do nott understand the below table? Read This Explanation to make the most out of it!
Grade for Turning
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | H10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Iscar | IC20 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Kennametal | KC5410 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | PVD | N05 - N20 | N | N | N | N | |||||
Kennametal | K313 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N10 - N35 | N | N | N | N | N | N | |||
Walter | WN10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N05 - N20 | N | N | N | N | |||||
Seco | KX | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Tungaloy | KS05F | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | uncoated | N05 - N10 | N | N | |||||||
Tungaloy | TH10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | uncoated | N10 - N20 | N | N | N | ||||||
Mitsubishi | HTI10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Sumitomo | H1 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | T | Turning | Uncoated | N10 - N30 | N | N | N | N | N |
Grade for Milling (Indexable)
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | H10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N05 - N15 | N | N | N | ||||||
Sandvik | H13A | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N15 - N30 | N | N | N | N | |||||
Iscar | IC08 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N05 - N20 | N | N | N | N | |||||
Iscar | IC28 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N15 - N30 | N | N | N | N | |||||
Kennametal | KC410M (KC510M) | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | PVD | N05 - N15 | N | N | N | ||||||
Kennametal | KC422M (KC522M) | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | PVD | N20 - N30 | N | N | N | ||||||
Walter | WXN15 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | PVD | N05 - N25 | N | N | N | N | N | ||||
Seco | H15 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N05 - N20 | N | N | N | N | |||||
Seco | H25 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N10 - N35 | N | N | N | N | N | N | |||
Mitsubishi | HTI10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N05 - N20 | N | N | N | N | |||||
Mitsubishi | TF15 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N15 - N35 | N | N | N | N | N | ||||
Sumitomo | DL1000 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | DLC | N05 - N25 | N | N | N | N | N | ||||
Sumitomo | DL2000 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | DLC | N05 - N30 | N | N | N | N | N | N | |||
Sumitomo | H1 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N15 - N30 | N | N | N | N | |||||
Sumitomo | H20 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | M | Milling | Uncoated | N20 - N35 | N | N | N | N |
Grade for Parting Off
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | GC1105 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | PVD | N05 - N30 | N | N | N | N | N | N | |||
Sandvik | H10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | Uncoated | N10 - N30 | N | N | N | N | N | ||||
Iscar | IC20 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Kennametal | KCU10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | PVD | N05 - N20 | N | N | N | N | |||||
Kennametal | KCU25 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | PVD | N20 - N30 | N | N | N | ||||||
Walter | WN13 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | Uncoated | N05 - N20 | N | N | N | N | |||||
Seco | HX | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | Uncoated | N10 - N30 | N | N | N | N | N | ||||
Tungaloy | TH10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | uncoated | N10 - N20 | N | N | N | ||||||
Mitsubishi | HTI10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | P | Parting | Uncoated | N05 - N30 | N | N | N | N | N | N |
Grade for Grooving
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | H10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | Uncoated | N10 - N30 | N | N | N | N | N | ||||
Sandvik | GC1125 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | PVD | N10 - N35 | N | N | N | N | N | N | |||
Iscar | IC20 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Kennametal | K313 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | Uncoated | N10 - N30 | N | N | N | N | N | ||||
Walter | WN13 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | Uncoated | N05 - N20 | N | N | N | N | |||||
Seco | 883 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | Uncoated | N05 - N30 | N | N | N | N | N | N | |||
Tungaloy | KS05F | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | uncoated | N05 - N10 | N | N | |||||||
Tungaloy | TH10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | uncoated | N10 - N20 | N | N | N | ||||||
Mitsubishi | HTI10 | N | N - Non-Ferrous (Aluminum, Brass, Plastic) | G | Grooving | Uncoated | N05 - N30 | N | N | N | N | N | N |
Recommended Insert Cutting Edge Geometry for Aluminium 7075
Honing Size: | 0.00-0.01 mm / 0.000-0.000" | |
Rake Angle: | 15° -25° | |
Land Angle: | Positive | |
Land Width: | 0.05-0.10 mm / 0.002-0.004" | |
Ground Insert: | Highly Recommended | |
Polished top: | Recommended |
Learn more about carbide inserts Cutting-Edge Geometry Parameters.