- Equivalent Standards
- Chemical Composition
- Cutting Speeds Recommendation
- Recommended Carbide Grades
- Cutting Edge Geometry
Material Ti-6Al-4V MIL (HT) Menu:
| General Information: | ||
|---|---|---|
| Material Group | S - Superalloys (Heat resistant and Titanium) | |
| Sub-Group | Titanium alloy | |
| Tensile Strength | [N/mm^2] | |
| Machinability Range | 15% - 30% | |
Watch the Video:
"How to use the Material Pages"
and get the most out of this page!
Equivalent International Designations for Material Ti-6Al-4V MIL (HT)
| Standard | Name |
|---|---|
| sae | 4906, 4920, 4928, |
| din | TiAl6V4 |
| uns | UNS R56400 |
| bs | TA10 TA11 TA12 |
| anfor | T.A6V;AIR:9183 |
Chemical Composition for Material Ti-6Al-4V MIL (HT)
Sorry, Not Availble for this Material
Cutting Speeds Recomendations for Titanium alloys
* Click on the speeds below for higher precision in specific conditions!
| Application | Vc (m/min) | Vc (SFM) |
|---|---|---|
| Turning | 60-120 | 200-390 |
| Milling | 45-90 | 150-300 |
| Parting | 40-75 | 130-250 |
| Grooving | 55-105 | 180-340 |
| Drilling | 55-105 | 180-340 |
Important! The speed estimation is given for an ideal situation:
- Most suitable carbide grade
- Stable tool clamping
- Stable workpiece clamping
- Good quality raw material
- A short overhang of the cutting tool.
- Nominal hardness of the material.
- etc.
Click on the speeds in the above table to get better precision for specific parameters
Or use our Speed and Feed Calculator
Recommended Carbide Grades for Material Ti-6Al-4V MIL (HT)
* If you do nott understand the below table? Read This Explanation to make the most out of it!
Grade for Turning
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | S05F | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | CVD | S05 - S10 | S | S | |||||||
| Sandvik | GC1105 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S15 | S | S | |||||||
| Sandvik | GC1115 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S20 | S | S | |||||||
| Sandvik | GC1125 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S30 | S | S | S | ||||||
| Iscar | IC806 (IC804) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S20 | S | S | S | S | |||||
| Iscar | IC807 (IC907) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S25 | S | S | S | S | |||||
| Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
| Kennametal | KCU10 (KC5010) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
| Kennametal | KCU25 (KC5025) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S30 | S | S | S | ||||||
| Walter | WSM10S (WSM10) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S20 | S | S | S | S | |||||
| Walter | WSM01 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S05 | S | ||||||||
| Walter | WSM20S (WSM20) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S30 | S | S | S | S | S | ||||
| Walter | WSM30S (WSM30) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S40 | S | S | S | S | S | ||||
| Seco | TS2000 (CP200) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S25 | S | S | S | S | S | ||||
| Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S25 | S | S | S | ||||||
| Seco | TS2500 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
| Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
| Tungaloy | AH8005 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S10 | S | S | |||||||
| Tungaloy | AH8015 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
| Mitsubishi | MP9005 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S15 | S | S | S | ||||||
| Mitsubishi | MP9015 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
| Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S35 | S | S | S | S | S | ||||
| Sumitomo | AC5015S | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S15 | S | S | S | ||||||
| Sumitomo | AC5005S (AC510U) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S10 | S | S | |||||||
| Sumitomo | AC5025S (AC520U) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S30 | S | S | S | S | S |
Grade for Parting Off
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | GC1105 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S20 | S | S | S | S | |||||
| Sandvik | GC1145 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
| Iscar | IC807 (IC907) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S10 | S | S | |||||||
| Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
| Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S25 - S40 | S | S | S | S | |||||
| Kennametal | KCU10 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S15 | S | S | S | ||||||
| Kennametal | KCU25 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S30 | S | S | S | S | |||||
| Walter | WSM13S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S20 | S | S | S | S | |||||
| Walter | WSM23S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S30 | S | S | S | S | S | ||||
| Walter | WSM33S (WSM33) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
| Walter | WSM43S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S30 - S45 | S | S | S | S | |||||
| Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S30 | S | S | S | S | S | ||||
| Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
| Tungaloy | AH7025 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S25 | S | S | S | ||||||
| Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S25 | S | S | S | ||||||
| Mitsubishi | VP10RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S10 | S | S | |||||||
| Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
| Mitsubishi | VP30RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S25 - S40 | S | S | S | S | |||||
| Sumitomo | AC520U | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
| Sumitomo | AC1030U (AC530U) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S |
Grade for Grooving
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | GC1125 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S30 | S | S | S | S | S | ||||
| Iscar | IC806 (IC804) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S15 | S | S | S | ||||||
| Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
| Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S25 - S35 | S | S | S | ||||||
| Kennametal | KCU10 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S20 | S | S | S | S | |||||
| Kennametal | KCU25 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S30 | S | S | S | ||||||
| Walter | WSM13S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S20 | S | S | S | S | |||||
| Walter | WSM23S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S30 | S | S | S | S | S | ||||
| Walter | WSM33S (WSM33) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S40 | S | S | S | S | S | ||||
| Walter | WSM43S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S30 - S45 | S | S | S | S | |||||
| Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S20 | S | S | |||||||
| Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S35 | S | S | S | S | |||||
| Tungaloy | AH905 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S10 | S | S | |||||||
| Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
| Tungaloy | AH7025 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
| Mitsubishi | VP10RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S10 | S | S | |||||||
| Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S25 | S | S | S | S | |||||
| Mitsubishi | VP30RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S25 - S40 | S | S | S | S | |||||
| Sumitomo | AC520U | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S25 | S | S | S | S | |||||
| Sumitomo | AC1030U (AC530U) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S40 | S | S | S | S | S |
Grade for Milling (Indexable)
| Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Sandvik | S30T | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S30 | S | S | S | S | S | ||||
| Sandvik | S40T | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S25 - S40 | S | S | S | S | |||||
| Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Iscar | IC830 (IC928) | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S20 - S40 | S | S | S | S | S | ||||
| Kennametal | KC510M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S10 | S | S | |||||||
| Kennametal | KC522M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S30 | S | S | S | S | |||||
| Kennametal | KCSM40 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S25 - S40 | S | S | S | S | |||||
| Seco | MS2500 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S05 - S25 | S | S | S | S | S | ||||
| Seco | F40M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Seco | MS2050 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S35 | S | S | S | S | S | S | |||
| Tungaloy | AH120 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S25 | S | S | S | S | |||||
| Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S25 | S | S | S | ||||||
| Mitsubishi | MP9120 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Mitsubishi | MP9130 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S35 | S | S | S | S | S | ||||
| Sumitomo | ACU2500 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
| Sumitomo | ACM200 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S10 - S30 | S | S | S | S | S | ||||
| Sumitomo | ACM300 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S20 - S40 | S | S | S | S | S |
Recommended Insert Cutting Edge Geometry for Material Ti-6Al-4V MIL (HT)
| Honing Size: | 0.02-0.05 mm / 0.001-0.002" | |
| Rake Angle: | 13° -18° | |
| Land Angle: | Neutral | |
| Land Width: | 0.10-0.20 mm / 0.004-0.008" | |
| Ground Insert: | Recommended |
Learn more about carbide inserts Cutting-Edge Geometry Parameters.
