Machining DataSheet for

General Information:
Material GroupP - Steel
Sub-GroupLow Alloy Steel
Hardness197.0 HB
Tensile Strength660 [N/mm^2]

Watch the Video:
"How to use the Material Pages"
and get the most out of this page!

Machining Steel A350LF2

Steel A350LF2 is a low-alloy steel with a carbon content of 0.3% and additional 1.8% content of manganese, chromium, nickel, and molybdenum.. (See details in the below table). Steel A350LF2 has a machinability rating of 73%.

Low alloy steels are very popular in machine shops. The small amount of alloying elements enhances their mechanical properties and hardenability without a significant sacrifice in terms of machinability.

You can find here a list of machinability Ratings for different Low Alloy Steels.


  • For general Turning of Steel A350LF2 at stable conditions use a grade with a Hard substrate and CVD coating.
  • In case you are running at a cutting speed that is lower than 490 SFM (150 m/min), it is better to use a grade with a
  • Hard substrate and PVD coating.
  • For general Milling use a grade with a Semi Hard substrate and PVD coating.
  • For detailed carbide grades recommendations, check the Below Chart, or use the Grades Wizrad.
  • Recommended Cutting speed range for turning at stable conditions is 890 - 1210 [SFM] / 270 - 370 [m/min].
  • Recommended Cutting speed range for milling with stable clamping and short overhang is 560 - 750 [SFM] / 170 - 230 [m/min]
  • For detailed cutting speed recomendations, check the Below Table, or use our Speed and Feed Calculator.

  • Equivalent International Designations for Steel A350LF2

    Standard Name

    Chemical Composition for Steel A350LF2

    Element Amount
    Manganese (Mn)0.6-1.35%
    Nickel (Ni)0.4%
    Copper (Cu)0.4%
    Chromium (Cr)0.3%
    Carbon (C)0.3%
    Silicon (Si)0.15-0.30%
    Molybdenum (Mo)0.12%
    Phosphorus (P)0.035%
    Sulfur (S)0.04%

    Cutting Speeds Recomendations for Steel A350LF2

    * Click on the speeds below for higher precision in specific conditions!

    ApplicationVc (m/min)Vc (SFM)

    Important! The speed estimation is given for an ideal situation:

    • Most suitable carbide grade
    • Stable tool clamping
    • Stable workpiece clamping
    • Good quality raw material
    • A short overhang of the cutting tool.
    • Nominal hardness of the material.
    • etc.
    Click on the speeds in the above table to get better precision for specific parameters
    Or use our Speed and Feed Calculator

    Recommended Carbide Grades for Steel A350LF2

    * If you do nott understand the below table? Read This Explanation to make the most out of it!

    Grade for Turning

    Grade for Parting Off

    Grade for Grooving

    Grade for Milling (Indexable)

    Recommended Insert Cutting Edge Geometry for Steel A350LF2

    Honing Size:0.05-0.08 mm / 0.002-0.003"
    Rake Angle:11° -13°
    Land Angle:Positive
    Land Width:0.20-0.30 mm / 0.008-0.012"

    Learn more about carbide inserts Cutting-Edge Geometry Parameters.

    Enjoy Ads Free Browsing !

    Are you tired of ads on our website? Become a premium user for Just 1.5 Dollars per Month and get rid of all the ads pop-ups.

    Scroll to Top