- Machining Guidelines
- Equivalent Standards
- Chemical Composition
- Cutting Speeds Recommendation
- Recommended Carbide Grades
- Cutting Edge Geometry
Material Ti-99.7 (Grade 3) Menu:
General Information: | ||
---|---|---|
Material Group | S - Superalloys (Heat resistant and Titanium) | |
Sub-Group | Pure Titanium | |
Hardness | 80.0 HRB | |
Tensile Strength | 510 [N/mm^2] | |
Machinability | 35% |
Watch the Video:
"How to use the Material Pages"
and get the most out of this page!
Machining Material Ti-99.7 (Grade 3)
Material Ti-99.7 (Grade 3) is a pure tianium material with a machinability rating of 35%.
Pure titanium grades exhibit excellent corrosion resistance in environments that include: calcium chloride, cupric chloride, various concentrations of acetic acid, and high-temperature seawater.
However, they lack strength and hardness when compared to titanium alloys such as Ti-6Al-4V. Therefore they are used in oil & gas components, reaction and pressure vessels, tubing systems and heat exchangers, or any other application where corrosion resistance and chemical stability are required but high strength is not needed.
Pure titanium is very ductile and needs to be machined with precision-ground and sharp cutting edges. The cutting tool needs to be either uncoated or have a very thin coating layer to preserve the sharpness of the cutting edge.
Summery:
Equivalent International Designations for Material Ti-99.7 (Grade 3)
Standard | Name |
---|---|
sae | Grade 3 B381F2 |
din | Ti-99.7 |
uns | UNS R50400 |
bs | TA2.5 |
anfor | AIR:9182T40 |
Chemical Composition for Material Ti-99.7 (Grade 3)
Element | Amount |
---|---|
Iron (Fe) | 0.3% |
Carbon (C) | 0.1% |
Cutting Speeds Recomendations for Material Ti-99.7 (Grade 3)
* Click on the speeds below for higher precision in specific conditions!
Application | Vc (m/min) | Vc (SFM) |
---|---|---|
Turning | 120-160 | 390-520 |
Milling | 90-120 | 300-390 |
Parting | 75-100 | 250-330 |
Grooving | 105-140 | 340-460 |
Drilling | 105-140 | 340-460 |
Important! The speed estimation is given for an ideal situation:
- Most suitable carbide grade
- Stable tool clamping
- Stable workpiece clamping
- Good quality raw material
- A short overhang of the cutting tool.
- Nominal hardness of the material.
- etc.
Click on the speeds in the above table to get better precision for specific parameters
Or use our Speed and Feed Calculator
Recommended Carbide Grades for Material Ti-99.7 (Grade 3)
* If you do nott understand the below table? Read This Explanation to make the most out of it!
Grade for Turning
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | S05F | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | CVD | S05 - S10 | S | S | |||||||
Sandvik | GC1105 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S15 | S | S | |||||||
Sandvik | GC1115 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S20 | S | S | |||||||
Sandvik | GC1125 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S30 | S | S | S | ||||||
Iscar | IC806 (IC804) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S20 | S | S | S | S | |||||
Iscar | IC807 (IC907) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S25 | S | S | S | S | |||||
Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
Kennametal | KCU10 (KC5010) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
Kennametal | KCU25 (KC5025) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S30 | S | S | S | ||||||
Walter | WSM01 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S05 | S | ||||||||
Walter | WSM10S (WSM10) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S20 | S | S | S | S | |||||
Walter | WSM20S (WSM20) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S30 | S | S | S | S | S | ||||
Walter | WSM30S (WSM30) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S40 | S | S | S | S | S | ||||
Seco | TS2000 (CP200) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S25 | S | S | S | S | S | ||||
Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S25 | S | S | S | ||||||
Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
Seco | TS2500 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S20 - S35 | S | S | S | S | |||||
Tungaloy | AH8005 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S10 | S | S | |||||||
Tungaloy | AH8015 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
Mitsubishi | MP9005 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S15 | S | S | S | ||||||
Mitsubishi | MP9015 | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S20 | S | S | S | ||||||
Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S15 - S35 | S | S | S | S | S | ||||
Sumitomo | AC5015S | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S15 | S | S | S | ||||||
Sumitomo | AC5005S (AC510U) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S05 - S10 | S | S | |||||||
Sumitomo | AC5025S (AC520U) | S | S - Superalloys (Heat resistant and Titanium) | T | Turning | PVD | S10 - S30 | S | S | S | S | S |
Grade for Parting Off
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | GC1105 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S20 | S | S | S | S | |||||
Sandvik | GC1145 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
Iscar | IC807 (IC907) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S10 | S | S | |||||||
Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S25 - S40 | S | S | S | S | |||||
Kennametal | KCU10 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S15 | S | S | S | ||||||
Kennametal | KCU25 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S30 | S | S | S | S | |||||
Walter | WSM13S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S20 | S | S | S | S | |||||
Walter | WSM23S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S30 | S | S | S | S | S | ||||
Walter | WSM33S (WSM33) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
Walter | WSM43S | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S30 - S45 | S | S | S | S | |||||
Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S30 | S | S | S | S | S | ||||
Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S | ||||
Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S25 | S | S | S | ||||||
Tungaloy | AH7025 | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S15 - S25 | S | S | S | ||||||
Mitsubishi | VP10RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S05 - S10 | S | S | |||||||
Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
Mitsubishi | VP30RT | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S25 - S40 | S | S | S | S | |||||
Sumitomo | AC520U | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S10 - S25 | S | S | S | S | |||||
Sumitomo | AC1030U (AC530U) | S | S - Superalloys (Heat resistant and Titanium) | P | Parting | PVD | S20 - S40 | S | S | S | S | S |
Grade for Grooving
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | GC1125 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S30 | S | S | S | S | S | ||||
Iscar | IC806 (IC804) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S15 | S | S | S | ||||||
Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
Iscar | IC830 (IC328) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S25 - S35 | S | S | S | ||||||
Kennametal | KCU10 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S20 | S | S | S | S | |||||
Kennametal | KCU25 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S30 | S | S | S | ||||||
Walter | WSM13S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S20 | S | S | S | S | |||||
Walter | WSM23S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S30 | S | S | S | S | S | ||||
Walter | WSM33S (WSM33) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S40 | S | S | S | S | S | ||||
Walter | WSM43S | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S30 - S45 | S | S | S | S | |||||
Seco | CP500 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S20 | S | S | |||||||
Seco | CP600 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S35 | S | S | S | S | |||||
Tungaloy | AH905 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S10 | S | S | |||||||
Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
Tungaloy | AH7025 | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S15 - S25 | S | S | S | ||||||
Mitsubishi | VP10RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S05 - S10 | S | S | |||||||
Mitsubishi | VP20RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S25 | S | S | S | S | |||||
Mitsubishi | VP30RT | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S25 - S40 | S | S | S | S | |||||
Sumitomo | AC520U | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S10 - S25 | S | S | S | S | |||||
Sumitomo | AC1030U (AC530U) | S | S - Superalloys (Heat resistant and Titanium) | G | Grooving | PVD | S20 - S40 | S | S | S | S | S |
Grade for Milling (Indexable)
Brand | Grade | ISO | Material | app | App | Coating | Apps Range | 05 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Sandvik | S30T | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S30 | S | S | S | S | S | ||||
Sandvik | S40T | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S25 - S40 | S | S | S | S | |||||
Iscar | IC808 (IC908) | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
Iscar | IC830 (IC928) | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S20 - S40 | S | S | S | S | S | ||||
Kennametal | KC510M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S10 | S | S | |||||||
Kennametal | KC522M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S30 | S | S | S | S | |||||
Kennametal | KCSM40 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S25 - S40 | S | S | S | S | |||||
Seco | MS2500 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S05 - S25 | S | S | S | S | S | ||||
Seco | F40M | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
Seco | MS2050 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S35 | S | S | S | S | S | S | |||
Tungaloy | AH120 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S10 - S25 | S | S | S | S | |||||
Tungaloy | AH725 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S25 | S | S | S | ||||||
Mitsubishi | MP9120 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
Mitsubishi | MP9130 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S15 - S35 | S | S | S | S | S | ||||
Sumitomo | ACU2500 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S05 - S25 | S | S | S | S | S | ||||
Sumitomo | ACM200 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | CVD | S10 - S30 | S | S | S | S | S | ||||
Sumitomo | ACM300 | S | S - Superalloys (Heat resistant and Titanium) | M | Milling | PVD | S20 - S40 | S | S | S | S | S |
Recommended Insert Cutting Edge Geometry for Material Ti-99.7 (Grade 3)
Honing Size: | 0.02-0.05 mm / 0.001-0.002" | |
Rake Angle: | 13° -18° | |
Land Angle: | Neutral | |
Land Width: | 0.10-0.20 mm / 0.004-0.008" | |
Ground Insert: | Recommended |
Learn more about carbide inserts Cutting-Edge Geometry Parameters.